ANYCUBIC 3D PRINTERS: RESIN AND FILAMENT FOR PROPS

Anycubic printers, compared for props.

Anycubic sells two kinds of 3D printer. The Kobra line prints filament, which suits helmets, armor and other large parts. The Photon line prints resin, which suits small parts with fine detail: emblems, greebles, jewelry and miniatures. This page lines up the printers Anycubic's US store had ready to ship on November 17, 2026, by what matters for props. PropBuilds prints its kits on Bambu Lab printers and has not tested an Anycubic printer, so every figure here is Anycubic's own.

PropBuilds earns a commission if you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases.

THE SHORT VERSION

  • Filament: the Kobra 3 Max V2 prints up to 420 x 420 x 500 mm, the Kobra S1 Max 350 x 350 x 350 mm, the Kobra X and Kobra 4 260 x 260 x 260 mm and the Kobra S1 250 x 250 x 250 mm.
  • The Kobra S1 and S1 Max are fully enclosed. The S1 Max also heats the chamber to 65 °C, which helps with ABS and ASA.
  • Resin: the Photon P1 Max prints up to 285.5 x 214 x 300 mm and the Photon Mono M7 Max up to 298 x 164 x 300 mm. The Photon P1 and Mono M7 Pro print 223 x 126 x 230 mm.
  • Resin prints need a wash and a cure after printing. Anycubic sells the Wash & Cure 3 machines for that.

The Anycubic line-up

Five filament printers, five resin printers and two add-ons that Anycubic's US store listed as shipping in 24 hours on November 17, 2026. Anycubic's prices change often, so none are shown here. Each card opens the live product page.

Which one fits what you want

For whole helmets and long props in as few pieces as possible, choose the Kobra 3 Max V2. For ABS or ASA armor, choose the Kobra S1 Max, which is enclosed and heats its chamber. For multicolor badges and display pieces, choose the Kobra X or a Combo. For small parts with fine detail, choose a Photon resin printer: the Mono 4 Ultra for small pieces, the P1 or Mono M7 Pro for a mid-size plate, the P1 Max or Mono M7 Max for the largest. Bigger models can be split into parts on any of them.

Six worth a closer look

Most room for big props

Anycubic Kobra 3 Max V2

Photo: Anycubic

Anycubic Kobra 3 Max V2

Filament / 420 x 420 x 500 mm / up to 600 mm/s

The largest printer in the Kobra line. Anycubic lists a 420 x 420 x 500 mm print volume, which it gives as 88 liters. That is tall and wide enough to print many full-size helmets, chest pieces and long props in one piece. Anycubic lists a recommended speed of 300 mm/s and a maximum of 600 mm/s, a bed that reaches 90 °C and auto-leveling. Multicolor printing needs the ACE 2 Pro, which the Combo version includes.

View on Anycubic ↗

Affiliate link.

Anycubic Kobra S1 Max

Photo: Anycubic

Anycubic Kobra S1 Max

Filament / enclosed / 350 x 350 x 350 mm

The large enclosed one. Anycubic lists a 350 x 350 x 350 mm print volume in a fully enclosed CoreXY frame, with active chamber heating to 65 °C, a hardened steel nozzle that reaches 350 °C and a 120 °C bed. A heated, enclosed chamber keeps big ABS and ASA parts such as armor plates from warping. Anycubic says it prints up to 16 colors with ACE 2 Pro units.

View on Anycubic ↗

Affiliate link.

Anycubic Kobra X

Photo: Anycubic

Anycubic Kobra X

Filament / 260 x 260 x 260 mm / up to 600 mm/s

A 260 x 260 x 260 mm printer that Anycubic sells as printing four colors on its own, which makes it the one to look at for badges, signs and multicolor display pieces. The Combo version adds an ACE 2 Pro, and Anycubic lists that as seven colors. Anycubic lists a maximum of 600 mm/s and a bed that reaches 100 °C. The Kobra 4 has the same print volume and prints one color.

View on Anycubic ↗

Affiliate link.

Largest resin plate here

Anycubic Photon P1 Max

Photo: Anycubic

Anycubic Photon P1 Max

Resin / 285.5 x 214 x 300 mm / 14-inch 12K screen

Anycubic's large resin printer. It lists a 285.5 x 214 x 300 mm print volume on a 14-inch 12K monochrome screen, with an X/Y resolution of 24.8 x 24.8 microns. That is enough room for a resin mask, a large bust or a full plate of small parts in one run. The Photon Mono M7 Max is the other large option: 298 x 164 x 300 mm on a 13.6-inch 7K screen at 46 microns.

View on Anycubic ↗

Affiliate link.

Anycubic Photon Mono 4 Ultra

Photo: Anycubic

Anycubic Photon Mono 4 Ultra

Resin / 153.4 x 87 x 165 mm / 7-inch 10K screen

The small resin printer. Anycubic lists a 153.4 x 87 x 165 mm print volume and a 7-inch 10K screen with 17 x 17 micron pixels, the finest X/Y figure on this page. It was the lowest-priced resin printer here when checked. It suits emblems, buttons, jewelry, greebles and miniatures, the small detailed parts that go onto a larger filament print.

View on Anycubic ↗

Affiliate link.

Anycubic Wash & Cure 3 Plus

Photo: Anycubic

Anycubic Wash & Cure 3 Plus

Wash and cure / cures up to 228 x 128 x 260 mm

Resin prints come off the printer coated in liquid resin, so they need a wash and then a cure under UV light. Anycubic lists the Wash & Cure 3 Plus with a maximum cleaning volume of 230 x 140 x 260 mm and a curing size of 228 x 128 x 260 mm, which covers the full plate of the Photon P1 and Mono M7 Pro. A smaller Wash & Cure 3 and a larger Wash & Cure 3 Max are also sold.

View on Anycubic ↗

Affiliate link.

FAQ

Should I get a resin or a filament printer for props?

Filament for large parts: helmets, armor, long props. Resin for small parts where fine detail matters: emblems, jewelry, greebles and miniatures. Many prop makers print the body in filament and the small detail parts in resin. The resin vs filament guide linked below covers the choice in more depth.

Which Anycubic printer is best for cosplay helmets?

The bigger the build volume, the fewer pieces a helmet needs. The Kobra 3 Max V2 (420 x 420 x 500 mm) and the Kobra S1 Max (350 x 350 x 350 mm) fit many full-size helmets in one piece. The Kobra X, Kobra 4 and Kobra S1 print a full-size helmet in a few parts. Use the helmet size calculator linked below to get the size of your own helmet first.

What does resin printing need besides the printer?

Resin, a wash and a cure for every print, gloves, and a room with good airflow, because liquid resin irritates skin and has fumes. Anycubic sells the Wash & Cure 3 machines and bundles some printers with one. Read the safety sheet for the resin you buy.

Which Kobra printers are enclosed?

Anycubic lists the Kobra S1 and the Kobra S1 Max as fully enclosed. The S1 Max also has active chamber heating to 65 °C. ABS and ASA warp when the air around the print is cool, so those two are the ones to choose for those materials. PLA and PETG do not need an enclosure.

What is the ACE 2 Pro?

Anycubic's multicolor unit. It holds four spools and dries filament at up to 65 °C while printing. Anycubic lists it as compatible with the Kobra 3, Kobra 3 V2, Kobra 3 Max, Kobra S1, Kobra S1 Max and Kobra X printers. The Combo versions include one.

Has PropBuilds tested these printers?

No. PropBuilds kits are printed on two Bambu Lab P2S printers. The figures on this page are the ones Anycubic publishes on its own product pages, read on November 17, 2026.

Why are there no prices on this page?

Anycubic changes its prices, discounts and bundles often, so they are not copied here. Each card opens the live product page, where the current price is shown.

Keep looking